How To Draw Kemono Wolf Head

Download Article

Download Article

Fursuits are creature costumes that can be used in a wide diversity of means. Well-nigh commonly associated with the furry community, fursuits are also commonly used for sports mascots and charitable causes. The head is the most complicated part of a fursuit, simply it also portrays the most character. Making your own fursuit head takes a long time, not to mention a whole fursuit, and so you may need some time.

1. ane

   Wrap foam around your head loosely and cut away any backlog. Wrap 1 inch (2.5 cm) thick foam around your head to get a sense of how broad the mould volition be. Aim to make it fit and then that you can skid it on and off without communicable your ears or nose. Mark where the foam meets in the back of your head, so cut away any backlog foam so the edges run across together.^[1]

   • Yous will stop upwardly with a piece of foam as tall as your head that will be rolled into a tube.

2. 2

   Glue the edges together with a hot glue gun. Take the sides of the foam and glue them together to create a tube. Do a picayune bit at a fourth dimension to allow the glue to cool until you have a straight, secure seam. Hold the edges together during this process to fully stick each side of the foam to the other.^[2]

   • After this, you lot should accept a tall tube that slides snugly over you with a chip of foam extending in a higher place your head.
   • Exist careful around hot glue and enquire someone to help you if you are worried about hurting yourself.

   Advertising

3. 3

   Circular the peak of the head by folding the peak cream together and snipping off the excess. Press the forepart and back of the top part of the foam tube into the center of the tube and glue them together. And then, fold in the correct side, and fold in the left side. Cut abroad excess foam and glue the parts you folded down together to grade a rounded pinnacle.^[iii]

   • Cutting away bumps and actress foam as much as y'all can, as this volition only brand the fursuit head look bumpy and uneven on acme.

   Advertisement

1. ane

   Describe eye holes on the front of the foam tube. The front end of the tube is where the seam is, so turn this towards you and describe eyes on either side of the seam. So, utilize scissors or a razor knife to cut the eyes out a footling smaller than your outline.^[4] Don't worry nearly getting them perfect, yous can always cut the eyes a flake larger afterward on.

   • This gives y'all an thought of where the residual of the features volition become, as you can place the muzzle and ears relative to the optics.
   • Wear the tube and brand a dot where your eyes are located to cutting more than accurately-located center holes. If y'all can't see through the foam, poke the foam gently to feel where your optics are located.

2. 2

   Layer cream on pinnacle of the base of operations to make eyebrow ridges and bulk up the face. Mensurate how large yous want your eyebrow ridges to be in a higher place the heart holes and draw the shape into some other piece of foam. And then, cut it out, and attach it to the eyebrow ridge area above the optics with hot glue.^[5] Add 2 more than layers of increasingly smaller size foam to create a rounded brow.

   • Utilise a long piece of shaped foam first for the base layer of the countenance ridge, then cutting smaller shapes to circular out the brow. This allows you to develop a thick brow above the eyes that juts out slightly from the forehead.
   • Countenance ridges are cracking for showing emotion on your fursuit head. Angle them in such a way that your character portrays its feelings through its eyes!

3. 3

   Add together ears by cutting out conical foam shapes and attach them to the head. Most real-life animal ears are conical in shape, meaning they are not flat and pointed simply have a bend. Once you've placed the ears in the right place for your fauna, cutting out ear holes to allow for ventilation in the headpiece.

   • Cut out a conical shape from cream by making a triangle with a rounded base, then bend the shape onto the dorsum-center surface area of the head and assess where y'all demand to cut to make it fit your character's animal. Mucilage down the bottom of the ears with hot glue.^[vi]
   • Look at the animal you want to portray and figure out how they show their emotions through their ears. For case, an alert dog'due south ears are perked upwards in the middle of its head, while a tired domestic dog will have drooping ears on each side of its head.
   • Consider looking at a template online to find the best arroyo for cut out convincing ears.

   Advertizement

1. one

   Expect at reference photos of your brute to determine its muzzle shape. A true cat has a short muzzle, while a wolf or a dog has a long one. Even though your fursuit caput will probable be cartoony, it'due south all-time to try to go an authentic idea of your creature'southward advent to translate it correctly to the foam head.

2. two

   Make a long muzzle by folding a piece of foam in half and indenting the front. Cut a piece of foam nearly 6–12 inches (15–30 cm) long, depending on the size of your animal's snout. Then, fold it in half, and button the forepart of the folded foam in to create the philtrum — the vertical groove beneath an animal's nose.^[vii] When you lot have finished forming the cage, hot glue information technology together and hold it tight with sewing pins equally it cools. Then, glue the end without the philtrum to the foam head.

   • Layer pieces of cream around the part of the cage that connects to the caput to blend it in naturally.

3. 3

   Make a brusk muzzle by layering cream in the shape of the snout. Written report the shape of your animal's muzzle, so cut out circular shapes to layer on elevation of each other. Smooth out the edges with scissors and proceed glueing on more foam until the snout begins to take 3D shape. Then, attach it to the face up on the oral fissure area.^[8]

   • If you lot accept very thick foam available (around 2–4 inches (5.1–10.2 cm) thick), it is easier to cleave out the entire shape of the cage at once and attach it.

4. iv

   Layer foam on at the seam betwixt the muzzle and the face up to create cheeks. The muzzle will abruptly transition from snout to confront, so use foam to shine out the seam and make the muzzle seamlessly blend in.^[nine] Form cheeks on either side of the cage with foam for the all-time choice to hide this seam.

   • Don't brand the cheeks poke out also far from the head as the fur you add later on will add a lot of depth to the head.

   Advert

1. one

   Wrap the head in plastic wrap and cover it with duct record, marking sections off. Afterwards finishing the foam head base of operations, tightly wrap the head in plastic wrap then embrace the plastic wrap with duct tape to form a duct tape shell. Then, section off each part of the head with a marker and label each department with its location on the head, for instance, the back and front end of the ears, the sides of the muzzle, the forehead and cheeks, etc.^[10]

   • Plastic wrap and duct tape make it simple to measure out fur later on, as you can remove it from the base of operations mask to cut the fur to the right size.
   • Mark the direction of fur as well equally the type of fur on the duct tape. Employ a minor pointer to indicate which manner the fur will menstruum off of the head and then you tin can employ it correctly afterwards on.

2. ii

   Cut away each section of duct record, then measure out it against your fur. Carefully cut away each section of the duct tape on the caput, then flatten it out against your chosen color of fur. You may need to cutting along folds to brand it lay apartment.^[xi] Make an outline of each slice against the fur, as if you lot are tracing your hand.

   • Don't worry if you accept to cut a piece of duct record to get information technology to lay apartment — as long as the fur is cut to the flattened shape, it will seamlessly fold dorsum into place on your foam base of operations.
   • Mark the underside of each outlined piece of fur with its location on the head and then you remember where to use each piece later on.

3. three

   Cutting out the fur and set the pieces to the side. Endeavor to conserve as much fur as you can past keeping the outlines shut together. And so, cutting out the outlines, and prepare them to the side.^[12] Don't pile the fur, keep them separated from each other so y'all tin can hands put them back together on the foam head in the right place.

   • Use fabric scissors or an X-ACTO pocketknife to go accurate cuts.

4. iv

   Lay the fur on your cream head, and so begin sewing the edges together. Lay the fur on the foam head to come across if you have cutting everything accurately. Remove ii pieces of side by side fur at a time and sew their corresponding edges together. Keep sewing adjacent pieces together until all of the fur is sewn, forming what might resemble a hirsuite mask.^[13]

   • If y'all cutting folds in the duct tape to brand them lay apartment, stitch these cuts dorsum together in your fur to return the flattened shape to its original, 3D form.

5. 5

   Glue the fur mask onto the cream base, starting with the muzzle and working back. Heat up your hot mucilage gun as you lay fur over the foam head. Make a thick layer of hot mucilage on the tip of the muzzle, then put the olfactory organ into the muzzle hole in the mask. Let it dry out, then continue calculation hot glue around the front of the face and pushing the fur into place.^[xiv] This may take a long time to get right, then put on some music or a show in the background.

   • The ears can be catchy if the mask is already glued to the eyebrow ridge — apply hot glue all around the edges of the ears and countenance ridge at the aforementioned time, so slot the foam ears into the ear holes of the fur mask and press down on both the ears and eyebrow ridge.
   • It's best to practice the muzzle commencement, then the cheeks and side of the face, then the eyebrow ridge and ears, and cease with the back of the head.

6. half dozen

   Shave away excess fur with an electric razor to your desired fur length. Become an electrical razor and shave downward the fur from its original, long length. If y'all want your character to be a bit raggedy, don't shave information technology all the way downwards, but if your character is meant to look clean and cropped, shave very shut to where the fur attaches to the foam base.^[fifteen]

   • Always shave away less than you think at starting time, as y'all tin shave more afterwards if it'south still too long, but you can't add together fur back once it's cut away!

7. 7

   Glue felt to the nose, eyebrows, and inside the muzzle for definition. Cutting out the shape of the eyebrows, the nose, and the oral cavity of your muzzle in accordingly colored felt — the nose might exist blackness or red, the eyebrows should be a slightly darker color than the facial fur, and the mouth may be a mix of a blackness bottom with a blood-red felt tongue in the middle. Utilize hot gum to the dorsum of each piece and stick it downwardly in its appropriate spot!

   • Yous can as well run up these features to the fur mask before glueing it downwardly, which can make them more secure and less probable to autumn off.

   Advertisement

Add New Question

• Question

  Are in that location whatsoever cheaper options when making a fursuit head?

  

  Alycia Ruiz

  Community Respond

  Yous could always get with a paper head if you're depression on coin. I used ane/two inch foam even though everyone else says to use one or 2 inch. If it'south your first suit, I'd say you should use 1/2 inch cream and cheap fur yous tin purchase on MoreFurLess, and maybe like one or 2 pieces of fur from Jo-Ann'southward. Be careful with Jo-Ann'southward fur, considering it may shed.

• Question

  How would you be able to breathe in a fursuit?

  

  Leopard star

  Community Answer

  In that location should be holes by the eyes, and if the fursuit has an opened mouth, there should exist a hole in the rima oris every bit well.

• Question

  How long does a fursuit usually accept to brand?

  

  Depends on the level of detail yous intend to put into it - your fursuit is a place to express your creativity, and then yous tin feel free to take as long as you desire to make it as detailed as you want or forgo such details in favor of having it washed sooner. Information technology's all upwards to your discretion.

• Question

  Do fursuit heads have padding in them if they're made by a professional person?

  

  Yes, they do. Fursuits made by professionals have plenty of padding then they are very comfortable to wear.

• Question

  Around how much is a fursuit to make yourself?

  

  Alycia Ruiz

  Customs Answer

  If you are getting fur for about $24 a thousand, and foam for about the same price, with everything else in betwixt, then about 200 at the least and 400 maximum for a full body if you are making information technology yourself. This is cheaper than a commissioned professional fursuit by a maker.

• Question

  What kind of sew together do y'all employ to sew the fur pieces together once you cut them out?

  

  The blazon of sew together totally depends on what your stitching. If information technology's an area in the head that will accept a lot of tug in it (like the neck), then the ladder stitch is a adept choice. When I make my head I use this run up a lot considering it'due south not sloppy and is very durable!

• Question

  How tin I go far machine-washable?

  

  Car washable heads can be tricky, simply you are able to make them. If the head is only foam, you should exist fine. Brand certain in that location are no airbrush marks either as those will come up off easily. The optics tin can be very catchy, but I recommend acrylic pigment. Make sure you don't add together electronics like fans, LEDS, or annihilation like that. And e'er put the washing machine to common cold and frail as normal setting will destroy the caput entirely.

• Question

  How much does it cost to purchase a fursuit?

  

  Skylar Wilson-Brown

  Community Answer

  Fursuits are ordinarily expensive. For the entire fursuit and all parts, a fursuit will be effectually $200 - $5000,depending on the item you put into information technology.

• Question

  Can I brand a fursuit caput with scales or feathers?

  

  LaurelBean

  Customs Answer

  Yous tin can make a fursuit head out of pretty much anything! Your inventiveness is what matters about.

• Question

  Where can I bay a fursuit?

  

  Pre-made fursuits tin exist constitute in various places. Depending on the maker, you lot can buy from an auction site or get them directly from a maker'due south social media folio or store. Yous can as well find them at furry conventions, if you happen to attend one. Also eBay may have options of premade fursuits.

Show more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertising

Things You'll Demand

• A few sheets of 1 inch (two.5 cm) foam
• Fleece or shag fur
• Colored felt
• Hot glue gun and plenty of hot glue
• Scissors
• Fabric pens
• Sewing needle

• Find pictures of other fursuits for inspiration, and don't be afraid to ask their creators about how they made their adjust — the furry customs is super open and helpful towards others making DIY suits.

• Make sure to picket YouTube videos on how to make i of these, a visual reference is always helpful.

• Set bated a whole afternoon to this project. If you want information technology to come out perfect, it'll take more just an hour or two!

• Await upward fursuit templates for your character online to find authentic blueprints and cutting layouts.

Thanks for submitting a tip for review!

Advert

• Be conscientious around scissors, X-ACTO knives, and other precipitous implements. Always cut away from your torso.

• Don't exist afraid to ask somebody else for help with sewing, glueing, or cutting the foam head.

Advertisement

About This Article

Commodity Summary 10

To brand a fur accommodate caput, yous'll demand 1-inch thick foam, glue, plastic wrap, duct tape, and fur. First past wrapping the foam around your head, and marking where the foam meets at the dorsum of your head. Then, cut away any excess foam and mucilage the edges together. Later on that, fold the top of the foam in, cut off any backlog foam, and glue the acme together. Once you've got the basic head shape, cut out foam ears and glue them to the sides of the head. You lot can besides fold a piece of foam in half and gum it on the forepart to brand a olfactory organ. After you've added all the facial features, wrap the head in plastic wrap and then duct tape so yous tin add together the fur. When you've covered the head, use scissors to advisedly cut the duct record into sections, such as the cheeks and forehead, stick the sections of tape to your fur, and cut them out with scissors. When you've cutting out all of the sections of fur, stitch them together with thread and mucilage them onto the mold of your head. For more than tips, including how to brand your fur adapt head'due south facial features more than realistic, read on!

Did this summary assist yous?

Thanks to all authors for creating a page that has been read 113,695 times.

Did this commodity aid you lot?

Source: https://www.wikihow.com/Make-a-Fursuit-Head

Posted by: pullenmrseach.blogspot.com

Share this post